MIL-PRF-19500-323 Semiconductor Device, Transistor, Pnp, Silicon, Switching, Types 2N3250A, 2N3251A, 2N3250Aub, 2N3251Aub, Jan, Jantx, Jantxv, Jantxvm, Jantxvd, Jantxvp, Jantxvl, Jantxvr, Jantxvf, Jantxvg, Jantxvh, Jans, Jansm, Jansd, Jansp, Jansl, Jansr, Jansf, Jansg, Jansh, Janhc, Janhcm, Janhcd, Janhcp, Janhcl, Janhcr, Janhcf, Janhcg, Janhch, Jankc, Jankcm, Jankcd, Jankcp, Jankcl, Jan...This specification covers the performance requirements for PNP silicon switching transistors. Four levels of product assurance are provided for each device type as specified in MIL-PRF-19500. Two levels of product assurance are provided for die. RHA level designators "M", "D", "P", "L", "R", "F", "G", and "H" are appended to the device prefix to identify devices which have passed RHA requirements.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15

MIL-PRF-19500/323N

4.4.2.3 Group B sample selection. Samples selected from group B inspection shall meet all of the following

requirements:

a. For JAN, JANTX, and JANTXV samples shall be selected randomly from a minimum of three wafers (or from

each wafer in the lot) from each wafer lot. For JANS, samples shall be selected from each inspection lot.

See MIL-PRF-19500.

b. Shall be chosen from an inspection lot that has been submitted to and passed group A, subgroup 2

conformance inspection. When the final lead finish is solder or any plating prone to oxidation at high

temperature, the samples for life test (subgroups B4 and B5 for JANS, and group B for JAN, JANTX, and

JANTXV) may be pulled prior to the application of final lead finish.

4.4.3 Group C inspection. Group C inspection shall be conducted in accordance with the conditions specified for

subgroup testing in table E-VII of MIL-PRF-19500, and as follows. Electrical measurements (end-points) and delta

requirements shall be in accordance with the steps of table IV herein.

4.4.3.1 Group C inspection (JANS), table E-VII of MIL-PRF-19500.

Subgroup

Method

Condition

2036

Test condition E; (not applicable for UB devices).

1,000 hours at VCB = 10 V dc; power shall be applied to achieve TJ = +150�C minimum and

1026

a minimum of PD = 75 percent of maximum rated PT as defined in 1.3 n = 45, c = 0.

The sample size may be increased and the test time decreased as long as the devices are

stressed for a total of 45,000 device hours minimum, and the actual time of test is at least

340 hours.

4.4.3.2 Group C inspection (JAN, JANTX, and JANTXV), table E-VII of MIL-PRF-19500.

Subgroup Method

Condition

2036

Test condition E; not applicable for UB devices.

RθJA and RθJC only, as applicable (see 1.3).

3131

Not applicable.

4.4.3.3 Group C sample selection. Samples for subgroups in group C shall be chosen at random from any

inspection lot containing the intended package type and lead finish procured to the same specification which is

submitted to and passes table I tests herein for conformance inspection. When the final lead finish is solder or any

plating prone to oxidation at high temperature, the samples for C6 life test may be pulled prior to the application of

final lead finish. Testing of a subgroup using a single device type enclosed in the intended package type shall be

considered as complying with the requirements for that subgroup.

* 4.4.4 Group D inspection. Conformance inspection for hardness assured JANS and JANTXV types shall include

the group D tests specified in table II herein. These tests shall be performed as required in accordance with

MIL-PRF-19500 and method 1019 of MIL-STD-750 for total ionizing dose, or method 1017 of MIL-STD-750 for

neutron fluence, as applicable (see 6.2 herein), except group D, subgroup 2 may be performed separate from other

subgroups. Alternate package options may also be substituted for the testing provided there is no adverse effect to

the fluence profile.

4.4.5 Group E inspection. Group E inspection shall be conducted in accordance with the conditions specified for

subgroup testing in table E-IX of MIL-PRF-19500 and as specified in table III herein. Electrical measurements (end-

points) and delta requirements shall be in accordance with table IV herein.